retro – Page 5 – Foxes Den

Bronica SQ-A / The Frankenstein project Pt:4

To find out what I am trying to accomplish with this project please refer to my initial post: Bronica SQ-A Medium format camera

Task:

To build a usable, basic issue, medium format camera (Bronica SQ-A) from damaged items and spare parts, for as little outlay as possible and shoot one black and white, and one colour roll of film as proof of its successful completion.

Getting started:

Building a camera from damaged parts is no easy task when the name happens to be a high end brand and any parts that are available, are being snapped up by others to service their own stock or to break up for sellable parts. I’m going to keep a running total to try and build this as cheaply as possible, and to keep track of this total I’m going to use my trusty Psion Organiser II LZ from 1989 to keep a tally.

Fourth purchases:

Now we have the bulk of the camera, we just need those annoying little bits to finish off. I’m calling them annoying, because if I was just to pay out for the 5 or 6 little finishing touches I need they would cost more than the total amount I have paid so far for the camera itself. I would be paying a premium for items that will in the end have no effect on the result I require to complete this project, that being two properly exposed rolls of film.

So here we go.

Battery:

Probably the cheapest item you will buy for this camera. The camera requires a single 6v alkaline battery and is quite important. Without it the mechanical shutter still works but at only 1/500 second. To obtain all the other available shutter speeds you need the battery to work the system electronically. This has cost me only £3:50GBP. After testing I can confirm that the battery works fine and all shutter speeds are as expected. Perfect.

Winding handle/Crank:

For some reason sellers always remove the crank prior to selling. That’s because the original Bronica crank is currently being sold at between £70-£80GBP and it really isn’t worth it. Everyone is after a quick buck and some people are willing to pay it. I’m not however, and my handle here is a special strength 3D printed version that I have paid the grand total of £11:20GBP for. It will need a couple of small “O” rings just to pad the handle on the spindle as it’s a tiny bit narrower than the original over priced one. It’s more than capable for the job in hand though, looks absolutely fine and has saved me around £65:00GBP of money.

The focussing glass:

This is another item that the sellers withold for individual sale. I wonder why? Yes a standard focussing glass is going to set you back anything up to £150:00GBP and again it’s not worth it. However my one is a “damaged” one in that it has handling and pen marks on it. It looks as if some has sadistically drawn their own frame on the glass, the fool! I’m hoping this will clean up a bit but as long as I can see the focussed image I’m not all that fussed. I only paid £11:75GBP for this so yet again a further saving of around £140:00. See, savings can be made, if you are happy to make the trade for a lower quality item.

Camera aperture covers:

Not really essential at this point, but to be honest you need to protect the fragile equipment you now have so it is really worth investing. I’m not purchasing these just yet, that’s a later purchase, I have a lens cover and hood cover now, so that is all I really need to start the real testing.

Waist level viewfinder:

Now this is a real bone of contention for me. Individually it is probably the most overpriced single item you could buy. It’s basically just a flip up hood that acts as a cover for the focussing glass, that affords a bit of light protection, as has been common on old twin lens cameras over the last century. But because the sellers again sell these as “additional items” they control the price and at an average of £150:00GBP (Recent eBay sales data) again the consumer is being ripped off. I’m currently monitoring some damaged ones for repair on the sale sites.

And as of the 4th May 2025 I am now the proud owner of one of these items. I’ve paid a total including postage of £39:75GBP and that’s a very fair price. I’ve been searching the sale sites for quite a time before coming across this one. There is one caveat though, it has some slight damage, but that’s what this site is all about and it ties in nicely with the Frankenstein aspect of this post.

Assessment:

I’m going to be very brief with the assessment, as you will see this project is made from a selection of parts that at time of purchase all had their own faults. Each part that has required repair has been highlighted in the relevant posts associated with this series. Links to those posts can be found in the link supplied in the first paragraph of this post. There are five parts in total. I’m generally pleased that the parts I have obtained have combined to make a very nice “Frankenstein” camera from a brand of camera that is becoming increasingly expensive as an “Antiquity”. Not that it was ever a cheap option for a camera in the first instance. Let’s move on to cover some repairs that have occurred for some of the pieces covered in this particular post.

Repairs:

The focussing glass as you will see above was in quite a poor state on its arrival. This one had some scars and it looks as if someone has used pen to draw their own frame in the glass, to be quite fair it was in quite a state, but it was purchased for a really low price and i believe it can be made to look a lot better. Listen to anyone who is,”in the know” and you will always be told to not handle these screens. A load of tosh, I’ve been handling these ground plane glass screens for years and sometimes you just need to get hands on and this is one of those cases. Yes, if it’s in a pristine condition then cotton gloves would be the order of the day, but this example bypassed pristine conditions many years ago.

Before: How the glass was received with scratches and ingrained ink

I started off with a good clean using IPA and cotton buds, I used about six cotton buds in this process using a new one every time the cotton was overrun with dirt.

Once the IPA clean had been done I then soaked the glass in a detergent solution and then again used cotton buds to get the solution into the scratched areas of the glass.

I’ve finished the clean with a rinse of hot water to remove all the solutions, and left the glass to dry on some paper roll. A light polish with a lint free cloth finishes the job.

After: all ink and dirt removed, only deep scratch remains but does not cause any issue with use

And this is how it all looks in the camera.

All looking fine in position in the camera

I’m extremely happy with the outcome with the glass, it does its job and works really well. With no distractions on the screen apart from a couple of scratches this item has been transformed. Just a little TLC and patience was all that was required.

The Winding handle crank doesn’t really have any issues, it just needs some aesthetic teasing. This crank was 3D printed for the ETRS version of the camera and as such the actual base of the crank shaft is slightly slimmer than that of the SQ model here. It works fine. I’m just being a bit of an OCD freak and want it to look better.

Before and after. “O” rings in place in the winder

Not a problem though as I only have to pack out about 4mm of space and I have just the thing to use. Two perfectly fitting minuscule “O”rings. Job done, let’s move on.

The Waist level viewfinder has one particular issue in that the folding action is slightly affected by an issue with the spring. Again it is fully usable and does not cause any issues operating wise, it is purely an aesthetic issue that I will get around to sorting once the camera has been tested.

This is one of those parts that has signs of age with small signs of wear and tear, however that adds to it’s character and shows it was once a very much loved item that saw some good usage.

I think, we are now ready to get the entire unit assembled and ready for the testing phase of this build.

Total Outlay:

So just how much has this little project actually cost? Over to my trusty Psion Organiser 2 LZ for a final update.

So the total cost of this project is £236.16GBP and I’m very pleased with that considering that sales for fully working similar cameras command prices similar to those seen in the picture below.

So taking this evidence into consideration, the route I have taken of building from damaged stock has saved me between £100-£350GBP. And as it is now a fully operational camera, I could probably command a price that would make a quite nice profit. But I’m not selling. This stays in my collection.

Outcome:

I want to take some pictures with both colour and Black and white film, to prove this camera is capable of this function considering it was constructed with broken or discarded parts.

Now complete, I have restored a beautiful piece of camera history

I will post some sample photos of the tests, and will also produce a couple of galleries to link to within this site. First I will try my luck with the Black and white film, as I have one here currently, though out of date it should suffice as it has been kept refrigerated during my ownership. I also have the chemicals and ability to develop film at home, so this should not be an altogether time consuming process.

This has been a satisfying build making a working piece of camera history entirely with damaged and alternative parts logged throughout all of these posts.

Look out for part 5 of this project that will cover the final testing and the results gained from these tests. Hopefully we will have some good photos and will then be able to wrap this project up.

Mo’ Money…(Boxes)

What the listing stated:

2x Tomy Robot money boxes.

One yellow with pound coin on hand and one orange with a dollar on his hand.

I don’t think either are working and the yellow one is missing the battery cover so selling as spares or repairs.

EBay

Those of you who follow this site will realise I purchased one of these a while back and did the repair here: Tomy – Mr.Money bank

I paid a total of £10:20GBP for the one in that repair post, and he is currently earning his keep at work collecting money for our local hospice charity – LOROS.

These two I have managed to get for a total of £19:26, so in theory these two are in the similarly price range as the other two. These were produced in 1987 to encourage children to save, with the element on a little bit of fun. These money boxes, when in a good, working condition do command a fair price. Just look at the screen grab of the latest prices being charged on the sale sites.

Both apparently, are not working and they do look quite disgustingly dirty, I’ve no idea what the actual faults are but I’d bet they centre around the switch area as that is a common issue. Add to that one of the battery covers is missing, and the price will rise by about another £5:86GBP as I get a new cover 3D printed, that will mean a total outlay of £25:14GBP or to be specific £12:57GBP per unit.

I more than likely will keep one of them and move the other one on. Let’s wait and see what arrives for us to begin the assessment.

Assessment:

Well, have a look at these two scruffy urchins that turned up today. Both in an absolutely filthy state, need a really good clean. It really surprises me that anyone can send such a filthy item through the post. Does it really take too long to just dust an item down with some furniture polish? Thankfully the wife wasn’t here when they arrived or else she wouldn’t have let them through the door 😂

That said they are as described. Everything is in place apart from the battery cover that I have already ordered as a new 3D print.

First thing to do is to clean them. They are filthy

One missing battery cover, a 3D replacement has been ordered

Setting a good example. My perfectly clean, and working example at the front

Apart from the above all seems fine. I have put a battery in each and turned them on, nothing happens. On the yellow example there is a little contamination on the battery contacts and when I move the battery I do get some motion but it sounds as if there is a sticking or broken gear inside. The orange example is totally dead but the contacts are clean. This could be the classic switch issue. So the order of the day is to get these both cleaned before dismantling just to keep any mess to a minimum, open them up, clean inside and check the gearings and then lubricate with some silicone grease. I’m hoping these will not be too labour intensive as I have been inside one of these before, and I’m more than aware of the issues of small parts falling out.

Repair:

First a clean with some polish.

Cleaning done, they’ve come up lovely, I’ll give them a final clean at the end after we’ve attended to the internal issues. So let’s get on.

I’ve chosen the orange chap first, however my suspicions about the faulty switch are wrong. The switch tests fine and I then go a bit deeper into its soul 😂

Off with his head and down into the cogs and sprockets

I get down to the motor and the cogs and sprockets and realise the motion has ceased. A little silicon grease over all the moving parts and a little bit of teasing and the unit springs into life. I let it run for a few minutes and then reassemble, cleaning everything along the way. This unit is now working.

The second unit, the yellow one, was working sort of. So as I have done above, this one was also stripped down, cleaned along the way and also had all cogs and sprockets greased accordingly. It also is now working fine.

I have already purchased a 3D printed battery cover to replace the missing one, and this is now installed, so we now have two complete units. For what I’ve paid for 3D printed pieces over the last year, it would probably be worth investing in my very own 3D printer.

The new replacement, 3D printed battery cover

Result:

Well I now have three absolutely perfect working examples of this fun piece of 1980s technology. One is in use earning money for the local hospice.

The Orange one is going to be used by a work colleague to raise money for the British Heart Foundation.

He is selling candles and I’m going to brand this one with a BHF logo to add some fun to his fundraising.

I have put together this little video regarding feeding time for these three . Enjoy!

Feeding time

The third unit will probably be sold on unless I can find someone else who can put it to good use.

Thanks for visiting, as you know it is always very much, appreciated.

Systema/Krypton – Horizon computerised travel chess set

What the listing stated:

The item has previously been owned before and unfortunately the batteries were left inside to corrode. When tested the computer part does not work.The pieces are a complete set for playing without the computer. Please see photos.

EBay

The unit looks clean cosmetically, and all the pieces are present. The computer side is not working probably as a result of the corrosion that is present in the battery compartment.

So I’ve paid a grand total of £11:49GBP for this unit which is probably slightly above its value. However it was from the St.Helena Hospice in Colchester, so I do not have an issue with this. In fact if I can get it working it will be donated straight back to a hospice I support here in Leicester – LOROS hospice. So all around, everyone benefits. I don’t play chess so it will not be used by me, I believe this unit was originally released circa 1996, so it is roughly 29 years old.

A really simple video, regarding how this unit works

Not much in the form of instructions online, however I have managed to get hold of some pictures of a quick start guide that should suffice for the moment. I’ll try and get full instructions from somewhere. In the meantime, the video above shows how easy it is to setup and use.

Let’s wait for its arrival to make an assessment.

Assessment:

The item has arrived and cosmetically it’s not too bad. There is some writing ink on the lid, and some staining on the base. but nothing that a good clean wouldn’t see to.

Open the battery compartment and all contacts are in serious need of a good clean or replacement. Battery corrosion is bad. All playing pieces are included and that’s always a bonus. I do believe that the issue here is purely to do with the acid corrosion, as when tested with a multimeter there is no continuity through the contacts. If the corrosion hasn’t gone too deep this should not be too much of a problematic repair.

Repair:

Now inside of the unit we can see the extent of the corrosion and thankfully it hasn’t reached the circuit board as the battery compartment sits just to the side of it.

I’ve disconnected the wires from the battery compartment so i can it take it away and concentrate on removing the contacts and cleaning them, or completely replacing them.

Removal of the contaminated battery contacts

The contacts are in such a poor state and so far beyond recovery that I have decided to replace them all. I need two single and three double AAA size contacts. Luckily I do have plenty of these in my current stock.

Prior to fitting the new contacts I will give the entire battery compartment a good clean with some IPA to remove the residual contamination. I will then dry the unit and just use some furniture polish to buff it all up and make sure it’s as clean as the day it left the factory. Once this is done the new battery contacts can be put in place. I can then re-solder the two internal battery wires back into place.

Contacts checked to see power is a available

New AAA battery contacts in place I just put in the batteries, to confirm continuity with the multimeter. A good 6.4v indicates this part of the repair is good and that the contacts are all working.

Next I’ve decided to replace the two wires from the battery compartment to the circuit board, as the wires, especially the negative one appears very brittle, probably a combination of age and the battery acid contamination.

I’ve tidied the wire run up by using some Kapton tape to secure it to the shell so there is no chance of a wire pinch.

Before closing the shell up, I use some hot glue to put the speaker back into place.

Now we can get the last four screws in place to secure everything together.

Then switch on…does it work? You betcha, it does everything that it’s meant to, and even though I don’t really know how to play, I do manage to challenge the computer for a good ten minutes. It’s been a great test run and even though I’m not that clued up it is working how it should and is now back in a perfect working order. I’ve created this little video below.

It’s working

Now just a little spit and polish and we can bring this repair to a close.

Result:

It’s polished up well apart from a bit of age staining on the rear, this makes no difference as it’s only the hidden part of the case and every game related part of the unit looks fantastic and it works just fine.

Really pleased with this especially as it’s going straight to our local hospice for them to sell on. It was brought from a hospice, and is going back to another, what better way to generate funds for them. I can’t play chess so this unit is wasted on me. Might as well pass it on to someone who’d appreciate it whilst giving some much needed financial support to a most worthy cause.

Another one saved from landfill. Win win all around.

Thanks for passing by and reading this post. It’s always very much appreciated.

Evistr L53 8GB voice recorder

What the listing stated:

Evistr L53 voice recorder – not working, parts only

EBay

I just wish the listings would be more specific, it’s not working because, (Fill blank spaces) you get my drift eh?

The unit looks good physically and cosmetically, and seems to have been well looked after, we just don’t know exactly what’s wrong with it. I’ll do some digging around and see if there are any generic problems, and I’ll also dig out some instructions just in case. It’s another one of those purchases where the cost of the item £2:24GBP has been out weighed by the postage, £2:45GBP however a total outlay of £4:69GBP isn’t all that bad in reality.

Current prices are in the £30-40GBP bracket. why you’d pay more for a used item confuses me, but then I’m usually easily confused.

I’ve downloaded some instructions, so we can hit the road running with some basic idea of how it works.

Let’s wait for it to arrive and then we can do an assessment.

Assessment:

Well, the box you see in the picture above, was just wrapped in some white A4 paper and put in the post. By the time it’s reached me the wrapping was split and the box hanging out. We are off to a flying start. It’s not the original box as that is for a 16GB version and this is an 8GB version, again no problem but probably used by the seller to beef up the offer.

The unit itself is quite smart looking, clean and generally free from any heavy marks with only light scuffs that you would expect after a few years of use.

It came with an audio connector, and some other bits that allow you to connect it to a phone system to record conversations.

The unit is dead and didn’t come with a micro usb charging cable, however again not a problem as I have plenty of these laying around. I’ve checked the charging port and I’m pleased to say it is in a good state and has no damage. So the first thing to do is to get some charge into the unit as the battery has probably been sitting dormant for quite a while. It was totally dead on arrival.

After a while I have turned it on to see if the charge is being taken and was greeted by this message, not one that I was expecting or one that I really wanted to see to be honest.

Disk Error. My immediate thought is that this is no longer recoverable, however, looking at known faults on their own site I might be able to recover the disk by using a Windows computer to access the disk. I’ll look at that option in the repair section of this post.

One thing I’m happy with is that the security tag on the back that covers the screw that allows access within, is still intact. I’m confident no one has yet accessed this unit internally. One less thing to worry about.

So realistically it’s a nice neat package in a very good cosmetic condition. It’s only problem that I can see at this very moment is the “Disk Error” issue.

Repair:

So let’s get this unit plugged in and see what we can do. It is really the only issue we have with this unit.

On my computer we have issues though. It’s a windows 11 machine and when plugged in, all the right sounds are made however nothing is recognised. Apparently the drivers for this unit are not supported on this windows system. It can’t see the drive. Damn that’s a problem.

Ok. I’ve had my thinking head on and just had a brainstorm. My brother in law over the road is notorious for not updating stuff. I called him and asked if he’d brought his new computer yet that he keeps threatening to buy and he says, “No, I haven’t Dave“. “Excellent” i tell him, get it warmed up as I’m coming over to use it.

I arrive at his house and he is curious as to what I want to do, I’m always going on at him to update and make his old computer safer, I keep telling him to upgrade it, and here I am asking to use it!

It’s a Windows 10 machine, slow is an understatement but he only uses it for casual browsing to be honest. I plug the cable in and then the recorder, I get a battery charging symbol and that is it. Hmmm.

Another brainstorm, I realise I’m using a charger only USB to micro usb cable instead of a data capable one. Another quick run back to my property and I take back a selection of cables. One of them worked, the drive was recognised and I was able to format the drive but I did it as Fat32. It worked to wipe the drive but I could not get the drive to boot up again without still showing a Disk Error message.

Disappointed I came home, I wasn’t giving up though. I dug out some other data cables from one of my old radio boxes and put it to my computer again, the drive didn’t show on the windows 11 system but it did something to allow me to be able to access the settings via the menu on the unit. I was able to go into settings and format the unit just as it should be via the units firmware.

After the format it indicated there were no voice records available, this was something I hadn’t seen before, we were finally getting somewhere.

It works, just have a look at the video below

All working

There are a lot of settings to play with in the unit. However the recording quality is superb if I say so myself, it’s so clear and balanced. The unit is now fully restored and working just perfectly. Add to that the fact that is cosmetically beautiful we now have a perfectly usable unit.

Result:

Working as well as the day it was purchased, this is probably the best £4:69GBP I have ever spent. A lovely unit, looks good, fits in the pocket nicely and has years of use ahead of it.

I’ve really enjoyed this little project, it’s been a right challenge and I was determined not to give up on it. I was glad that I persisted and got it working again.

I wonder how many of these units, or those very similar to it have just been thrown to waste, when they were in fact very repairable. Well this one has been saved, and will be usable for many more years to come yet. (And I now know how to fix it, if it ever does break again😂)

Thanks for passing by. Always very much appreciated.

Monty plays scrabble

What the listing stated:

UNTESTED

The product is a vintage Scrabble game titled “Monty Plays Scrabble,” released in 1984. It is a rare find and comes in its original boxed packaging. The game is a portable computer console version of the classic Scrabble game, making it unique and collectible. Please note that the functionality of the game is untested.

EBay

Why did i buy? I don’t know, maybe because its from 1984 and fits my modus operandi. To be truthful i looked at it, saw the wear and tear on it and thought to myself that i can make it look better. It also states it’s a rare find….its not. In good old EBay style its “Untested” which probably means they have put some batteries in, it doesn’t work, so let us use the get out clause of selling it as untested. I could however be very wrong, and just be using unnecessary sarcastic commentary, i suspect it’s very much the latter.

Here’s a little history:

Manufactured by Ritam Corp, under licence from J.W Spear and sons PLC 1984

A portable electronic device that plays a competent game of Scrabble. Up to three players may challenge the device. Each player enters one’s own name and subsequently the turn order in which they will play. The players can decide to draw their own tiles or let the device do the randomizing. If the device assigns the tiles, the players may ask the device to suggest a play by using the “Hint” option.

Players keep track of the gameboard using the paper pad provided or use their own gameboard. The device has a LCD readout that is only eight characters by four characters and cannot display the entire board. Players use the arrow keys of the membrane keyboard to scroll around.

All standard Scrabble rules apply. The device will challenge any word played that is not in its 12,000 word vocabulary. The human player is final arbiter however.

The device is powered by four “C” batteries or an AC adapter. Two Advanced Vocabulary Modules were available. Each module added 16,000 words to the machine’s vocabulary to bring the total to 44,000.

Boardgamesgeek.com

And I’m fortunate to have those two advanced vocabulary modules already installed, so this unit has the full vocabulary range of 44000 words. Lucky me. Apparently the unit is able to do 2 million calculations a second, but can take up to 3 minutes to make a move! With a vocabulary built in of 12,000 words that must mean it does a lot of questioning of itself prior to making a decision. I love a computer system that constantly doubts itself, it’s such a human trait.

Anyway, what’s arrived and how does it look. And is it working?

Assessment:

The parcel has arrived and been unpacked.

On taking the unit from the box there is no damage cosmetically, the keyboard is a bit dirty and the silver lettering and edging has worn a little.

Great news is that the battery contacts are in a perfectly clean condition with no sign of corrosion

Super clean and the two extra vocabulary modules

With no corrosion visible, I put some batteries in. I switch the unit on and it makes sound, great. Looking from directly above it looks as if there is some writing on the screen but this doesn’t become visible until you move to about 60 degrees away, a bit closer to the base of the unit.

So the pleasing thing is that it works. In general it is in a very good condition, coming with instructions and playing sheets. As always with items such as this from this time period, there is the expected smell of age induced mustiness, and there isn’t a great deal I can do about this. But I do seem to have a working unit that just requires a little maintenance and cleaning.

Repair:

I’ve had a quick clean of the front keypad and it was quite dirty.

Bit dirty just after a very brief clean of the keyboard

I’m not sure but I might open up the unit and give it a proper wash, I’ve got to have a look at the screen inside as I suspect the screen quality might be improved by replacing some old electrolytic capacitors that I suspect may be around that area. I could however be wrong. Let’s get it opened up then.

The board looks really clean on both sides, all capacitors (and there were only three of note) look good.

I have taken all three capacitors in the immediate screen area off, I’ve measured them out of circuit and they are all within the 10% tolerance of their indicated ratings so in my eyes there is no issues here. They are working fine.

All capacitors tested and within tolerance

On the rear of the board behind the display is a small variable capacitor. I turned this slightly to the left whilst under power and the screen quality has improved sufficiently be able to view the display from a more natural position. It can’t be adjusted any more though so it is now at its limits, probably a result of its age and limits of performance being reached for that particular component.

To be honest I’m satisfied everything inside the unit is fine, and the slight improvement to the display is more than adequate, I’m now going to close the unit back up and will concentrate on the exterior.

I’ve given the exterior a good polish, and then in my art box I have a silver permanent marker that will be great for touching up the worn out lettering and surrounds, so I will use this just to make the unit look a little more aesthetically pleasing.

And boy has that made it look better

Looking good as new, and with that result we can say the repair is complete.

Result:

We now have a good looking fully restored and fully working unit. It looks as good as the day it was sold and still does what it was made to do. The screen is at its limits but should last a good while yet. A smart looking 41 year old unit that has been saved from the scrap heap and will be around for a good time yet.

All clean, look at the restored lettering

Here we have a small video of its basic operation

Easy to operate even without instructions

All in all another satisfying repair, and yet another item saved from landfill. If it’s damaged, 9 times out of ten it can be repaired and reused. We don’t need to be so wasteful.

Thanks for following the repair, it’s always very much appreciated.

Thank you 🙏

Tradional pub skittles

My wife is a fantastic organiser. The family owes an awful lot to her as she always arranges meals and get togethers keeping us all in touch. Without her doing this I very much believe we’d all lose contact quite rapidly. She keeps the family together. And she is brilliant at what she does.

Today is one of those days, Easter Saturday, she has hired the Skittle alley at our local pub and we are all meeting there for a meal prior to throwing our “Cheeses” at the skittles. No perfectly round balls here, these are good old solid wood, full of splinters and shaped more like tin cans to be honest. And they can go off in any direction, there is no way to control them. Just don’t get in their way!

We play it differently up here in the East Midlands as can be seen here:

In the East Midlands, people play Long Alley in which the projectiles are rough balls or small capsule shaped logs called “cheeses” and a score is only made if the cheeses bounce a single time just in front of the pins.

Wikipedia

It can be quite brutal. But that’s how we roll in the East Midlands 😂

It’s a beautiful old pub, and we kind of adopted it when we moved up here. A right old traditional pub. I think there is about 22 of us up there tonight from all different areas, so it should be a nice evening.

Tomorrow is a different story when we will all be off to watch our home football team get slaughtered at home to our visitors- Liverpool.

But let’s not get too depressed about that, here’s how today has gone instead.

Paul wins the skittles

4 rounds of 3 cheeses each and we had sorted out the final four of the contest, cousin Paul wins outright and wins the first prize a Cadbury crème egg. Highest score of the evening went to niece Julie who managed to down eight skittles in one round.

Overall winner Paul, and high scorer Julie.

The remainder of the evening was just people talking and catching up. It was a lovely day and My wife has already sorted out the Christmas party dinner. She’s so damned organised.

The day started at our house earlier when everyone went down our garden pub to play darts, have a drink and kick the day off in a really fun and friendly fashion. It’s ended around 12 hours later when the tiredness sets in and people start to make their excuses and gradually filter off into the night.

Tomorrow we go again when we meet at my nieces home for her house warming party. It’ll be a little more subdued as some are back to work on Monday, however I’m really looking forward to meeting up with them all again.

Good times. Good company. Nothing beats it.

R36S (Clone) Handheld games console

What the listing stated:

Item is for spares repair only. Powers on but appears to be stuck on game.

Please view photos for details of listing

Any questions please message me

EBay

R36S game console. Boxed. Good condition externally

Here’s the info:

Whether you missed out on the gaming golden age of the 2000s or want to introduce your kids to those unforgettable classics, the R36S Retro Handheld Video Game Console supports 15,000 iconic games, making it your gateway to reliving the magic. It’s the perfect way to take a nostalgic trip back and rediscover the joy of childhood favorites.

Revisit your childhood memories with the R36S. Whether you’re rediscovering the excitement of Super Mario, the thrill of Pokémon, or the challenge of Zelda, the R36S brings your favorite games back to life.

Perfect for those who want to experience the magic of the 80s and 90s games all over again.

Equipped with dual joysticks, L/R bumpers, and a vibrant 3.5″ HD IPS display at 640×480 resolution, the R36S Retro Handheld Video Game Console delivers precise control over gameplay mechanics and stunning visual clarity. Enjoy enhanced color accuracy and fine details for a gaming experience that perfectly blends nostalgia with modern innovation.

r36s.co.uk

I’ve managed to secure this item for an all in price of £16:25GBP and thats including the postage. The seller had a number of these selling, I suspect they are customer returns as they still have screen protection, they are in original boxes with stickers on them, and that makes me suspect they are returns.

I think I may have paid over the odds for this unit.

The fact that as soon as this batch were purchased, another set had taken their place on the selling platform confirms this. On the r36s.co.uk site, these consoles retail at around £65:00GBP, you can get similar items from other Chinese outlets that are considerably cheaper. This is an emulator unit that runs via the Linux operating system, and is supplied ready installed with around 15,000 games already on the unit utilising a number of gaming system platforms. As the operating system is open source, you can also add additional games should you wish to do so. The one I have purchased is stuck on just the one particular game i believe. I think I have some work to do.

I very much suspect the issues with this unit lays solely with the software and are not in anyway hardware related. I could however be very wrong. My knowledge on these systems is very limited so I’m going to be very reliant on information and tutorials that i can find on line.

And i may as well download some operating instructions prior to its arrival, just to be a step ahead and furnished with the most basic knowledge of its operation, maybe then i won’t come across as a totally clueless clown.

Assessment:

It’s arrived and cosmetically it’s fine. It just doesn’t work. It doesn’t even do what is stated in the listing. More EBay untruths.

Powers on, charges ok and that’s about it. Box looks nice. Finding it hard to talk of anything else positive. Oh, and it’s not an original it’s a clone machine… cheapo copy. Any way, let’s have a look at getting it to work.

Repair:

So first thing was to download a new OS for the unit, unzip it, and download it to the removable sd card, easier said than done. I think I’ve probably lost all the games that were installed, but without a system to run it all, what’s the point. I can always download games later, I have however backed up a number of files as suggested so let’s just wait and see.

Trying to prepare the new volumes on the drive

The first operating system downloaded did not work, because now I’ve been informed that this machine is one of many clones out there, it’s not original. Lovely. Not a problem, we can still get another operating system, it’s just going to take a bit more of my time to do so, and god knows how long it will take to download the games. This is the biggest pain in the ass with these systems, the sourcing of the programs to ensure the system runs smoothly.

But it will be repaired. And I’m in no rush. I’m off out for a while.

I have had to download an alternative operating system ArKos_K36_v2.0 to my computer. It then has to be run through a disc imager programme to prepare the disc and install the correct partitions and system information, onto the micro SD card used by the unit.

That all done, time to plug the card into the unit and see if it turns on.

Hallelujah! It works.

The operating system successfully installed

Having to format the original card obviously erased all the games that were originally on the card. There were around 15000 games on this unit, but let’s be honest most of them would have been games that were either inferior, similar to others, or just used to bloat the card out. I’m now in a position where I can be choosy about the games I load on the system, and this will allow me to not have it so cluttered.

This is where it gets a little more tricky.

There are a number of people and sites I have spoken with or looked to, to find out the information required to carry out these tasks. And for someone who hasn’t messed about with computer and program files and structures for many a year it is quite daunting to say the least.

I have downloaded a file that is recommended and contains many of the 15000 games originally on the card but with a lot of the bloatware removed to make it a more structurally pleasing and easier to handle package. It’s called the Tiny best set go package and is downloaded from GitHub.

These games are broken down into Rom packages and have to be removed from the download and placed into the easyrom folder on your operating system, it’s a little more complex that that but that is the crux of the task. I won’t go into finite detail as it will bore your asses off and there is plenty of information on how to do it already out there.

I will recommend this one guy as having a superb little site regarding hand held consoles such as this and their issues: Handheld database

Anyway the task has been completed. I’m probably not going to get involved with such time consuming repairs as this again. It’s been a learning curve, but just too time consuming for me. I’ll leave these issues for the younger generation.

Result:

It works. It’s been saved from landfill and there is no better outcome than that. To be honest it’s unbelievable that so many games and so much information can be held on such a small memory card.

In general the game quality is really good, only let down sometimes by the way that the emulator software interprets the program in question. There is more than enough on here to keep anyone occupied during some downtime. There are many classic old school games on here that will also keep the old farts like me amused as well.

Overall it’s been a tough repair, I pretty much knew from the start what the issue would be and went into this repair totally blinkered. I have learned a lot from it, but will I be working on these again? I doubt it unless one of the younger members wants one then I might have another go. But until then it’s job done, another bit of throwaway hardware saved from the scrap heap.

Edit: I couldn’t keep away could i? I found a chap local to me who works on these units, and he has kindly offered to assist me if I should ever need anything clearing up. Well I couldn’t resist that offer and in two emails he has shown me just how to get these games downloaded, it’s simple when you know how.

So simple that rather than download a few games I’ve gone a tad over the top and now have 19939 of them. That should see me right beyond my natural existence and into the afterlife. What a lovely fellow. There are still lots of nice and helpful souls around.

Success.

Thanks for passing by, it’s always appreciated.

Nintendo Gameboy Printer

What the listing stated:

Listing for a FAULTY Nintendo Gameboy printer unit.

The printer is FAULTY, it has a lot of battery leakage in the battery compartment, so doesn’t currently power up. Some of the terminals look like they should clean up pretty well, but i cannot guarantee.

As it doesn’t power up, i haven’t been able to test it. So can’t guarantee thats the only issue.

The casing has some discolouration, marks and other imperfections here and there.

I haven’t attempted any repairs and cannot guarantee it is fixable.

SOLD AS FAULTY/spares/repairs.

EBay

Here are the supplied pictures:

Serious yellowing, good candidate for Retrobrighting

Some serious battery leakage contamination

I think I’ve got my work cut out with this one. It’s another piece of unloved technology from 1998 looking for a new life. I’ve paid a total of £19:89GBP including postage for this item, probably at the higher end of what I’m comfortable with for an item in this condition. It has some serious corrosion issues that could go a lot deeper than just the battery contacts. There is a definite issue with discolouration, however I’m happy with that as it will be my guinea pig for my first attempt at retrobrighting, this process i discussed in this post a few days back: Retr0bright – What’s that then?

My plan of attack for this unit is to completely dismantle it, give it a thorough clean, retrobright the casing and then attend to the electrical / component issues.

Here’s some history about the printer unit:

The Game Boy Printer, known as the Pocket Printer in Japan, is a thermal printer accessory released by Nintendo in 1998 which ceased production in early 2003. The Game Boy Printer is compatible with all the Game Boy systems except the Game Boy Micro and is designed to be used in conjunction with the Game Boy Camera. It also prints images from compatible late-generation Game Boy and Game Boy Color games. It runs on six AA batteries and uses a proprietary 38mm wide thermal paper with adhesive backing, originally sold in white, red, yellow and blue colors. In Japan, a bright yellow Pokémon version of the Game Boy Printer was released, featuring a feed button in the style of a Poké Ball.

Wikipedia

If I manage to get this into a working state it will be added to my GameBoy collection.

I just need a suitable lead to connect between the console and the printer, and a small roll of 38mm wide thermal paper. I’m currently sourcing these.

Assessment:

Well it certainly has the yellowing issues and I will cover that in a separate post where I will have my first attempt at Retrobrighting the unit. With batteries in place, the unit is very dead and no matter how many times the switch is operated, it remains dead. Battery terminals are a mess and there is a lot of evidence of battery leakage and corrosion.

Serious yellowing over the years visible at all angles

Serious corrosion across battery terminals

The board inside hasn’t been that badly affected by the corrosion, however one track from the battery terminal was showing signs of decay and will need attention. There are parts of the board that will need reflowing as there are some dodgy looking solder joints.

I’m happy that all the issues have been identified and I do actually have the items to carry out the repair. I will focus on the external issues such as the yellowing before dealing with the contacts and main board issues. Stay with me now, the repair begins.

Repair:

The Retrobrighting process for the shell assembly can be found in a separate post here: First attempt at Retrobrighting.

Needless to say the results are fantastic and I shall look at incorporating this method into more of my future projects. I have since given the case a second treatment and it is pretty much perfect with no sign of discolouration.

As you can see in the pictures above, the battery compartment suffered from some severe acid contamination. Using a grinding pen and a lot of cleaning solution, three of the five contacts were saved but two were beyond repair and I had to replace these with new contacts.

I then loaded the battery compartment with new batteries and then checked the two terminal ends to assure continuity, this was confirmed and continuity exists throughout. As a result the battery issues and power supply have now been resolved.

I mentioned that one of the tracks on the main board was showing signs of corrosion. I filed this down, cleaned it, and then brushed the board down with IPA and checked the continuity and this was fine. All suspect solder joints have also been reflowed, they are all looking good and new.

Track issue in the top left area by the battery contact. All corrosion ground off and cleaned with IPA

Area of concern highlighted on the left side picture. All attended to and cleaned and recoated with some solder mask to prevent any further decay

I had previously removed the motor from the board to assist with cleaning, as i didn’t wish to damage any of the ribbon cables. I then reconnected the cleaned and freshly repaired board, to the restored battery compartment to see if anything lit up. It sure did.

This was pleasing as it now showed that we had continuity from the battery compartment to the board. I then added the motor back in and we also had some movement.

Movement restored

This again was very pleasing as everything we have done so far seems to be working. However it proves nothing yet until I can get the correct cable and some correct sized thermal paper to see that it actually does print, or even advance the paper. Those items are being sourced, and I don’t want to jump ahead of myself just yet as there could still be a number of yet to be addressed issues that may arise. It’s very much a fingers crossed period until we can test the unit properly.

Let’s clean all the other plastics whilst we await all the other items to be attended to.

Now we will commence reassembly.

All restored, working and looking pristine

Now all assembled the motor moves into position when turned on, the feed button also works. The paper rolls for these units are at the moment extortionate and selling for about £10GBP for the tiniest of rolls, and I’m not paying that. I have a thermal printer at home and I have cut some of this paper to size to test the transport, and this works just fine. Just awaiting the cable to connect the GameBoy to the printer. Fingers still firmly crossed.

Result:

I’ve just found out that if you hold the feed button whilst turning on the unit you get a test message. I’ve done this and I’m pleased to say the unit is fully working.

I’ve also connected it to my game boy and the game – Pokemon pinball, and was able to print off the high scores. It truly works.

I’m just so pleased how this project has gone. It has been a complete refurbishment, clean, and I have even managed to reuse the original stickers. The unit looks pristine and really is a nice piece of kit. This goes into my GameBoy collection and has many more years of good use left in it.

And to think this would have probably ended up in landfill. Scandalous. The cost of repair to me has been less than £2GBP and the majority of that was for the peroxide solution to do the Retrobrighting.

Great result. Very happy with this.

I can now uncross those fingers. All is fine.

Thanks for passing by, as always most appreciated.

Tomy – Mr.Money bank

What the listing stated:

Not working

May be an easy fix

EBay

Now I don’t half buy some junk to fix, but this one struck a chord with me. Looking into its history I believe it’s a toy made to encourage children to save money from around 1987. So he’s currently around 38 yrs old.

Dirty, as per usual and a bit beaten up. Sounds just like me 😂

As you can see in the photo above, you could originally buy a set of these, incorporating Dollar, Pound or Euro stickers for the serving hand, the one i have made an offer on is the dollar one.

What appeals to me about this item is that I’ve been looking for a way at work to raise some money for the local LOROS hospice, and this might be a fun way to do it if I can get it working. I plan to brand it with the local hospice details and just thought it would be a fun way to use it. This is a fun object where you put a coin on its hand, its mouth opens, the eyes go up and the coin goes in the mouth. There is a munching motion and then the tongue licks its lips. Or at least it should do. This one I have ordered is having none of that and this is the challenge ahead. These units are notorious for having issues with the power switch, a simple fix if that is the case, but this is me…nothings ever that simple.

And as usual it’s dirty, has marks on it and needs a good clean.

As with everything retro (New antiques 🤦‍♂️) items are attracting some crazy prices, though I do think the general public are not as stupid as the sellers seem to believe they are, as all the above listings have yet to attract any bids. Now the one I have bid on is broken, and yes it has its battery cover. My current bid is £6.70GBP and I must now wait to see if it is a winning bid. With postage (Rip off as usual) the price will be £10.20GBP in total, so compared to the prices in the listings above it is an absolute bargain.

Good news – I have won the auction at this price. Nice.

Assessment:

Well, he’s arrived and just like Frankenstein he’s very dead. He needs an electrical kick start and that’s what we need to do. He’s obtained a lot of scuffs and marks but I think these will buff out. Cosmetically everything is there, even the battery cover and that pleases me immensely. With batteries in place there is not even the tiniest sign of life even if the on /off switch is operated many times. We need to get inside and take a look. Hopefully it’s not too big an issue.

He’s a little dirty, beaten up and scarred

And I’m just so happy he has a battery cover. Exceptionally rare and unexpected.

Repair:

I’ve headed straight for the switch as this is where there is usually trouble and straight away there was a problem. There was no continuity at the switch when operated, so this was removed, opened, cleaned and the brass contacts ground and cleaned. The switch was then reassembled and tested and was all ok.

No continuity, so dismantled, cleaned thoroughly and reassembled

But this was not the problem. Damn it, I now have to take it apart and there is a lot of mechanical items within.

Once dismantled I’ve had a good rummage around and have checked voltages around the electrical circuits until I found no voltage at the motor. The culprit was a small 3inch length of wire that had been crushed. This was replaced and the continuity was now restored to how it should be but still there was no life. I was confident that the electrical issues were no more so it must be a mechanical issue. There is a part of this unit that involves a tongue 👅 that pokes out. This was our issue. The cog and lever system had somehow been knocked out of sync, and once put back into its correct position the unit has now sprung into life. See the little video of this stage below:

We have life

Happy with this I’m now going to review all the pictures that thankfully I’ve taken, and ensure it’s reassembled and cleaned as I go along. The marks and dirt have buffed out nicely and the unit is now extremely clean and looking as good as the day it was purchased. And it works:

Working perfectly

Result:

Here it is now in all its highly polished and clean glory

Looking Beautiful and handsome in its 38th year.

Thoroughly enjoyed this little project, I love the electro mechanical items from this period, they really get you thinking.

This unit is now going to have a LOROS hospice logo placed on it to cover the Tomy one as discussed at the beginning of this post. We can then start to gather all that loose change in my work place to pass onto them. They need every penny we can raise. Every penny helps, especially in the current financial climate.

Thanks for passing by, as always it is very much appreciated.

First attempt at Retrobrighting

I’m currently deep into a repair project that I will be posting about on here shortly. However the shell of this project has aged so badly it has earned the right to be my Guinea pig for my first attempt at Retrobrighting, it deserves a separate post of its own, so it’s getting one. I have explained what Retrobrighting is in a previous post: Retr0bright – What’s that then?

The unit is a recently purchased and damaged Nintendo Gameboy printer from around 1998, it isn’t working and looks right ugly. It needs some attention to its fascia and battery base, so let’s get on to it.

I have taken the entire unit apart, separated the parts that need to be treated, removed all labels, and given the offending items a thorough wash in detergent before drying them off.

All stickers and other items removed. Shell thoroughly washed.

Next I’m just putting a 40 Volume 12% Peroxide cream solution into a small bowl, and I will then place the shells on a piece of cling film where I will liberally coat the offending items, using a brush, with the solution. When I’m happy with how this has gone, the treated surfaces will then be wrapped in cling film and placed in a sunny position for around 12hrs to allow the sun to do its thing. (UV lamps are sufficient if you have one available). I must reiterate it is important to wear protective gloves and eye protection when using this solution.

I’ve given a good coating of peroxide formula to all surfaces, but is it enough? I won’t know for at least a further 10-12 hrs, time will tell.

With the peroxide now applied, the fascia’s are now all wrapped in cling film and ready for 10-12 hrs or so of intense sunbathing. (Sounds just like me on one of our visits to Cyprus!). So let’s wait a while.

I’ve checked in and looked at the pieces outside, and after just 4hrs the results so far look amazing. I’m going to give it the full time though, so I’ll be back in around 6-8 hrs to check results. Hopefully we will have sufficient sunlight until then.

I’ve terminated the process at 9hrs as I have to go out and I’m impatient. Boy am I impressed at how it has turned out, it looks like a new shell.

Well I can honestly say that this treatment does work. I’m so impressed at the outcome, I just wish I’d attempted it earlier on some of my other products.

Anything I’d do differently? I’d probably slap on a little more solution or maybe even reapply about half way through the process, the only reason for this is that there is the most minute tiny tinge of a yellowing on the side that had the heaviest contamination, possibly if I hadn’t been so impatient and left it for 3 more hours it would have been sorted, but then again it might not have! I do think a further application at the halfway point, especially when an item is so heavily stained as this unit was, would have done the job and made it look even more perfect.

Am I coming across as disappointed? Well I can assure you I am not. It’s my first attempt and I am so impressed. The total outlay for this process was £1:85GBP and that was just for the 75ml bottle of peroxide from a local supermarket, and I have enough left for another 3 applications, an absolute bargain. We only learn and improve from being persistent, and I’ve already learnt from what I have attempted today. And i am already a better, and more knowledgeable person than I was only a few hours earlier. You certainly can teach an old dog new tricks.

Edit: some 12hrs later I have decided to give a second treatment to see if this can improve on that slight yellowing I mentioned earlier. The results have greatly improved the look and there is now no visible sign of yellowing. I’d certainly recommend a second treatment for heavily stained items. It works, extremely well.

Watch out for my next post regarding the repair of this printer and its reconstruction: Nintendo Gameboy printer

Thanks for passing by. Always appreciated

Task:

Getting started:

Fourth purchases:

Assessment:

Repairs:

Total Outlay:

Outcome:

Rate this:

Share this:

Assessment:

Repair:

Result:

Rate this:

Share this:

Assessment:

Repair:

Result:

Rate this:

Share this:

Assessment:

Repair:

Result:

Rate this:

Share this:

Assessment:

Repair:

Result:

Rate this:

Share this:

Rate this:

Share this:

Assessment:

Repair:

Result:

Rate this:

Share this:

Assessment:

Repair:

Result:

Rate this:

Share this:

Assessment:

Repair:

Result:

Rate this:

Share this:

Rate this:

Share this: